HS-DHH-EPC13-TV-XH5-P1.3 Four-Key Instant Electric Water Heater PCBA
Designed for instant electric water heaters, this customizable four-key PCBA supports 85–280 VAC input, 3.0–7.0 kW power settings, 30–55°C control, quick temperature presets, flow sensing, temperature learning, setting memory, and multiple protection functions.
# HS-DHH-EPC13-TV-XH5-P1.3 Four-Key Instant Electric Water Heater PCBA
The HS-DHH-EPC13-TV-XH5-P1.3 is a customizable instant electric water heater PCBA designed for household and commercial point-of-use water-heating equipment. Combined with the HS-HX-3526-4KEY-C1.0 display board, it integrates four-key touch operation, wide-voltage input, adjustable power control, quick temperature presets, water-flow sensing, automatic temperature learning, and multiple protection functions.
The display board uses a BYD control IC in a 28-SOP package, providing a practical control platform for customized instant water heater applications.
## Wide-Voltage Power Supply
The standard switching power supply version supports an input voltage range of 85–280 VAC, making the controller suitable for markets with different mains voltage conditions. An optional transformer-based solution supporting 180–265 VAC is also available.
During internal sample verification, the switching power supply version operated continuously for eight hours at 280 VAC without abnormal behavior. The transformer version also completed an eight-hour continuous operation test at 265 VAC.
## Adjustable 3.0–7.0 kW Power Control
The controller provides five configurable power settings:
- 3.0 kW
- 4.0 kW
- 5.0 kW
- 6.0 kW
- 7.0 kW
While the controller is off, pressing and holding the preset key for ten seconds opens the power-setting menu. The selected power level is automatically saved after three seconds without key operation.
The final rated power depends on the complete appliance design, including the heating element, power components, wiring, terminals, water circuit, and heat-dissipation structure.
## Simple Four-Key Touch Interface
The control panel provides four touch keys:
- 38°C, 42°C and 45°C preset key
- Temperature decrease key
- Temperature increase key
- Power on/off key
Pressing and holding the increase or decrease key for more than one second enables continuous temperature adjustment. Each valid key operation is confirmed by an audible buzzer tone.
The touch interface can operate through a 4 mm glass panel or a 2 mm plastic panel, allowing manufacturers to adapt the controller to different appliance housings and front-panel designs.
## Clear Operating Display
After power is applied, the display performs a one-second full-screen check accompanied by one buzzer tone. In standby mode without water flow, the screen displays “--”.
The display can indicate:
- Actual outlet water temperature
- Selected temperature
- Water-flow status
- Heating status
- Intelligent constant-temperature operation
- Excessive water-flow warning
The default standby temperature is 38°C. After water flow is detected for approximately three seconds, the controller activates heating. A flashing decimal point indicates active water flow and heating, while the indicator remains off when no water flow is detected.
## Intelligent Constant-Temperature Control
The adjustable temperature range is 30–55°C. The quick preset key cycles through 38°C, 42°C and 45°C, giving users convenient access to commonly selected temperatures.
A 50K NTC sensor is used for temperature detection. The control program supports automatic temperature learning, calibration, and parameter memory.
Under sample test conditions with a 25°C inlet temperature and flow rates of 1.5–3.0 L/min, the tested 36–48°C setpoints stabilized within 20 seconds after initial learning and calibration.
## Water-Flow Detection
The tested activation flow rate is 1.4 L/min, while the shutoff flow rate is 1.0 L/min. Heating is therefore coordinated with the detected water flow to reduce unintended operation without sufficient water circulation.
An LL indication is available when excessive water flow is detected, helping users identify conditions that may affect the outlet temperature.
## Integrated Protection Functions
The instant electric water heater control board supports multiple diagnostic and protection functions, including:
- Over-temperature protection
- Leakage-current protection
- Inlet temperature sensor open-circuit detection
- Inlet temperature sensor short-circuit detection
- Outlet temperature sensor open-circuit and short-circuit detection
- Zero-crossing fault detection
- Excessive water-flow indication
- Audible fault warning
- Automatic or power-cycle recovery according to the fault type
When the detected temperature reaches 60°C or above, the controller stops heating. Heating automatically resumes after the temperature decreases to 50°C.
The leakage detection range is 15–25 mA, with a measured sample value of 22 mA.
## Sample Reliability Verification
The sample completed several internal verification tests, including:
- Eight-hour continuous operation at 280 VAC
- Eight-hour testing at 85°C and 85% RH
- Complete-appliance dielectric testing at 1,800 V and 5 mA for one minute
- Fluorescent-lamp switching interference testing repeated 30 times
- Normal-temperature water testing
- Constant-temperature testing at different temperatures and flow rates
The specified controller operating environment is −15°C to 85°C with a relative humidity range of 10–95% RH. The test report notes that maximum heating output is reduced to approximately 2 kW below 0°C, so the final appliance rating should reflect the intended operating environment.
## Application Scenarios
This four-key instant electric water heater PCBA is suitable for:
- Instant electric shower heaters
- Wall-mounted electric water heaters
- Kitchen instant water heaters
- Washbasin water heaters
- Compact household hot-water appliances
- Commercial point-of-use water heaters
- Customized OEM and ODM water-heating equipment
## OEM and ODM PCBA Manufacturing
With 15 years of PCBA manufacturing and product development experience, SunSam provides hardware development, firmware programming, SMT assembly, wave soldering, display-board production, functional testing, traceability management, and volume manufacturing services.
The board dimensions, connectors, display icons, key layout, power settings, temperature range, protection thresholds, sensor logic, and control program can be customized according to the customer’s appliance design.
From prototype verification to volume production, SunSam provides complete instant electric water heater PCBA solutions for appliance manufacturers and brand customers.
Phase I of TianfuLai International Industrial City, Rongui Town, Shunde District, Foshan City, Guangdong Province, China
Looking for a reliable PCBA supplier? Contact SUNSAM for customized PCBA heater, PCBA refrigeration and washing machine PCBA, free samples, and competitive wholesale pricing. Get a quick quotation today.
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy